Wyoming WYDOT CDL General Knowledge Practice Test 4
Test 4 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Wyoming test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. An oncoming vehicle drifts across the center line into your lane. What is usually the safest move?
Show answer
Answer C: Steer to the right, toward the shoulder if necessary
Moving right keeps you away from the drifting vehicle and off the oncoming side; the other driver may swerve back and hit you if you go left.
-
2. A driver behind you wants to pass and you can see that the road ahead is clear. What should you do?
Show answer
Answer B: Do not signal the other driver to pass; let that driver decide when it is safe
Directing other drivers can cause a crash if you misjudge the gap, so leave the decision to the driver who is passing.
-
3. How can a driver restart the 60 or 70 hour on-duty limit?
Show answer
Answer B: Take 34 or more consecutive hours off duty
A period of 34 or more consecutive hours off duty resets the 60 or 70 hour calculation so the driver can begin a new period.
-
4. Where are the OVERSIZE LOAD signs normally carried on a vehicle moving under such a permit?
Show answer
Answer A: On the front and the rear of the vehicle
The warning signs face the traffic that meets the load and the traffic that comes up behind it, so they go on the front and the rear.
-
5. A chain rated at 6,600 pounds is fitted with a hook rated at 4,700 pounds. What is the working load limit of that assembly?
Show answer
Answer A: 4,700 pounds, the rating of the weakest part
An assembly is only as strong as its weakest component, so hooks, binders and links all count and the lowest rating governs.
-
6. How is free play in the steering wheel measured during the inspection?
Show answer
Answer B: By turning the wheel until the front wheels just start to move and noting the movement
Play is the movement at the rim that produces no movement at the road wheels, so it is measured by turning until the wheels first respond.
-
7. You are loading a flatbed that has no sides or bulkheads. How must the cargo be held?
Show answer
Answer D: By tiedowns, blocking or bracing, since there are no walls to keep it from shifting or falling off
Open decks depend entirely on securement devices; every article must be tied down or otherwise immobilized so it cannot move, spill or fall.
-
8. What is the correct order for a double clutch downshift?
Show answer
Answer D: Release the accelerator and push the clutch to reach neutral, release the clutch and press the accelerator to raise engine speed, then push the clutch again and select the lower gear
A lower gear turns faster than the one being left, so engine speed has to be raised in neutral before that gear will engage cleanly.
-
9. During the walkaround you notice one tire on an axle is a radial and the tire next to it is bias-ply. What should you do?
Show answer
Answer B: Treat it as a defect, because radial and bias-ply tires must not be mixed on the same axle
Radial and bias-ply tires flex and grip differently, so mixing them on one axle makes the vehicle handle unpredictably and is not allowed.
-
10. Your vehicle is stopped just past a hill or curve that hides it from approaching traffic. How should the warning devices be adjusted?
Show answer
Answer A: Move the rearmost device farther back, up to 500 feet, so drivers are warned before the obstruction
When a hill or curve blocks the view, the farthest device is moved back beyond the obstruction so approaching drivers see the warning in time.
-
11. Under Wyoming law, if an existing commercial driver license holder wants to upgrade to a higher class or add an endorsement that requires a skills test, what must the driver first obtain?
Show answer
Answer D: A new commercial learner permit
Wyoming statute requires every commercial driver license holder to obtain a commercial learner permit before upgrading to a higher class, adding an endorsement, or removing a restriction that requires a skills test.
-
12. What is the correct way to make a right turn in a long vehicle?
Show answer
Answer D: Keep the rear of the vehicle close to the curb and swing wide only as you complete the turn
Swinging left before a right turn invites another driver to move into the gap on your right, so any extra width is taken as the turn is finished.
-
13. A dock crew loads and straps the freight. Who is responsible for the load being legal and secure on the road?
Show answer
Answer D: The driver
Even when someone else loads and secures the freight, the driver must inspect it and remains responsible for it while driving.
-
14. On a one way street or a divided highway, where are the warning devices placed?
Show answer
Answer B: About 10 feet, 100 feet and 200 feet back toward the approaching traffic
When traffic can only come from one side, all three devices are spread out behind the vehicle to give approaching drivers a longer warning.
-
15. How are the headlights, marker lights and turn signals checked during the seven-step inspection?
Show answer
Answer A: The engine is shut off, the parking brake is set, the lights are switched on and then checked from outside the vehicle
The lights are switched on with the vehicle secured, then the driver walks around and confirms each lamp actually works and is clean.
-
16. You need to pull off onto the shoulder because of a problem with the load. How should you communicate that to other drivers?
Show answer
Answer D: Signal the move, then switch on the four-way flashers once stopped
Other drivers need a signal before you leave the lane and a clear warning once the vehicle is stopped near the traffic lanes.
-
17. You find one lug nut missing from a wheel that has ten studs. What should you do?
Show answer
Answer C: Treat it as a defect and have it repaired before the vehicle is driven
Every missing fastener loads the others more heavily, and wheel separations usually begin with one nut that nobody replaced.
-
18. Why must cargo also be held down against vertical movement and not only against sliding?
Show answer
Answer D: Because a load that bounces can jump the blocking and slacken its own tiedowns
Rough road makes an unrestrained article lift; every bounce lets it move a little and works the tiedowns loose until nothing is holding it.
-
19. Your brakes have failed and you decide to use the parking brake to slow down. Why should you hold the release button or lever while doing so?
Show answer
Answer D: So you can release the brake at once if the wheels lock and the vehicle starts to skid
The parking brake can lock the wheels; keeping your hand on the release lets you let go the moment a skid starts and regain control.
-
20. Why should you never back under a trailer whose landing gear is resting on soft or muddy ground?
Show answer
Answer C: The landing gear can sink or collapse and the trailer can drop or tip over
Soft ground lets the landing gear sink under the load being transferred to it, and a trailer that drops or topples during coupling is extremely dangerous.
-
21. You are pulling away from a curb in a 65 foot combination. Besides traffic, what must you watch?
Show answer
Answer B: The trailer wheels, which stay close to the curb and can strike it or an object on it
Because of off-tracking, the rear wheels follow a tighter path than the front, so they stay near the curb while the cab is already out in the lane.
-
22. What are you checking on the mud flaps during the walkaround?
Show answer
Answer C: That they are securely attached, not torn and not dragging on the ground
A flap that is torn or hanging loose stops shielding following traffic from spray and stones, and a dragging flap can catch and tear away on the road.
-
23. You are unsure whether your vehicle will fit through a narrow gate. What should you do?
Show answer
Answer A: Stop, get out and look, and take another route if the space is not clearly enough
Clearance is never guessed at from the seat; you look at it on foot and go round rather than trying a gap that may be too tight.
-
24. What does Wyoming law impose on a CDL holder convicted of serious moving violations such as following too closely or texting while driving a commercial vehicle?
Show answer
Answer B: A 60-day disqualification for two serious violations in a three-year period, and 120 days for a third or subsequent conviction
Under W.S. 31-7-305 two or more serious violations within a three-year period bring a 60-day disqualification, and a third or subsequent conviction brings 120 days.
-
25. How should a commercial driver treat the speed posted for a curve?
Show answer
Answer B: As a limit set for cars in good conditions, so a heavy or tall load calls for a lower speed
Posted curve speeds are based on passenger vehicles in good conditions, and a tall or heavy load can roll over well below that speed.
-
26. What is checked in step six of the seven-step method?
Show answer
Answer D: The turn signals and the stop lights, checked from outside the vehicle
Step six returns to the cab to switch on the signal and stop lamps, then checks each one from outside, because those lamps are not lit during the earlier light check.
-
27. You have just passed another vehicle on a two lane road. What tells you it is safe to return to your lane?
Show answer
Answer B: You can see the whole front of that vehicle in your right mirror
Seeing the entire front of the vehicle you passed in your mirror proves you are far enough ahead to move back over without cutting the driver off.
-
28. During the walkaround inspection, where does the driver normally start and how does the check proceed?
Show answer
Answer C: At the left front of the vehicle, working around it in a set order that returns to the cab
The walkaround follows the same route every time, starting at the left front and circling the vehicle, so that nothing is skipped when the driver is tired or rushed.
-
29. A tire blows out at highway speed. What should the driver do first?
Show answer
Answer C: Hold the steering wheel firmly, stay off the brake and let the vehicle slow down
Braking while a tire is gone can pull the vehicle out of line, so the driver keeps it straight and lets speed fall before easing off the road.
-
30. Under the federal hours of service rules, when must a property-carrying driver take a 30 minute break?
Show answer
Answer C: After 8 cumulative hours of driving time
Driving is not allowed after 8 cumulative hours of driving time without at least a 30 consecutive minute interruption of driving.
-
31. How does a driver measure following distance in seconds?
Show answer
Answer A: Wait for the vehicle ahead to pass a fixed roadside object, then count the seconds until the front of your vehicle reaches the same object
Counting from the moment the vehicle ahead passes a landmark until you reach it turns a gap you cannot judge in feet into a number of seconds.
-
32. You have backed into the same loading bay every week for a year. How often should you still get out and walk to the rear before backing?
Show answer
Answer D: Every time, since the area can change while you are away from it
A familiar space is no guarantee; vehicles, pallets, people and overhead obstructions appear between one visit and the next, so you check on every occasion.
-
33. Which step of the seven-step inspection method comes immediately after checking the engine compartment?
Show answer
Answer D: Start the engine and inspect the inside of the cab
Once the hood is closed the driver moves to the driver seat, starts the engine and checks gauges, controls and warning devices before going any further.
-
34. What should you check about the tire valve stems during the walkaround?
Show answer
Answer D: That the stems are not cut, cracked or leaking and the caps are in place
A split stem or a missing cap lets air escape or lets dirt into the valve, and either one can flatten a tire between stops.
-
35. You are dropping a loaded trailer in a yard. How far should the landing gear be lowered?
Show answer
Answer A: Until the pads make firm contact and the trailer weight is just off the fifth wheel
Cranking down until the gear is firmly on the ground and just lifting the load off the fifth wheel makes the trailer stable and lets the tractor pull out cleanly.
-
36. How does bracing differ from blocking when securing cargo?
Show answer
Answer B: Bracing runs from the upper part of the cargo to the floor or walls to keep it from moving, while blocking fits snugly against the cargo
Blocking is shaped to fit against the front, back or sides of a piece of cargo; bracing supports it from above so it cannot tip or shift.
-
37. Dry bulk tanks call for extra caution mainly because of what?
Show answer
Answer C: A high center of gravity combined with a load that can shift
Dry bulk loads ride high and can move inside the tank, which makes the vehicle easier to tip in a curve.
-
38. You are the first to arrive at a crash. What is the correct order of actions?
Show answer
Answer C: Protect the area, notify the authorities, care for the injured
Preventing a second crash comes first, because an unprotected scene puts the injured and the helpers in more danger than the original collision.
-
39. A vehicle becomes unsafe while you are already on the road. What does the federal rule allow?
Show answer
Answer A: Continuing only to the nearest place where repairs can safely be made
If stopping where you are would be more dangerous than moving, the rule allows you to reach the nearest place where the vehicle can safely be repaired, and no further.
-
40. Which description matches controlled braking during an emergency stop?
Show answer
Answer D: Apply the brakes as hard as you can without locking the wheels and keep steering movements small
Controlled braking keeps the wheels rolling just short of lockup, which gives the shortest stop while you keep the ability to steer.
-
41. Under federal rules, which commercial vehicles must stop at every railroad crossing before proceeding?
Show answer
Answer D: Passenger buses and placarded hazardous materials vehicles
Buses carrying passengers and vehicles required to display hazardous materials placards must stop at crossings, while other commercial vehicles slow and check.
-
42. You pick up a trailer that another driver dropped in the yard. What must you do before pulling it?
Show answer
Answer B: Inspect it yourself, because you are responsible for the whole vehicle you drive
Responsibility follows the driver who moves the vehicle, and a trailer that has stood in a yard may have lost air, developed a flat tire or been damaged.
-
43. Which lights should be used in fog, by day or by night?
Show answer
Answer A: Low beams and fog lights, together with the four-way flashers
High beam light bounces back off the water droplets and makes seeing worse, while low beams, fog lights and flashers help you see and help others see you.
-
44. You are told a posted bridge ahead has a weight limit lower than your gross weight. What must you do?
Show answer
Answer C: Take a route that avoids it, because a posted limit is a legal limit
A posted structure limit must be obeyed exactly as any other weight limit, so a heavier vehicle has to be routed around it.
-
45. On a tractor with a sliding fifth wheel, what does moving the fifth wheel forward do?
Show answer
Answer A: Puts more of the trailer weight onto the steering axle
Moving the coupling point forward transfers weight from the drive axles to the steering axle, which is how a driver corrects a drive axle that is over the limit.
-
46. An intermodal container is being carried on an ordinary flatbed rather than on a container chassis. What does that mean for securement?
Show answer
Answer B: It must be secured with tiedowns that meet the container securement requirements
A container carried on a vehicle that is not fitted with integral locking devices has to be secured to the deck with tiedowns that satisfy the rules for containers.
-
47. The brake pedal goes to the floor in a vehicle with hydraulic brakes. What can you do to build some braking pressure?
Show answer
Answer B: Pump the brake pedal rapidly, which may bring back enough pressure to slow the vehicle
Pumping can restore some hydraulic pressure; along with downshifting and the parking brake it is one of the ways to stop when the pedal fails.
-
48. What is Wyoming's minimum legal tire tread depth for tires used on the front wheels of a bus, truck, or truck tractor?
Show answer
Answer D: 4/32 inch
Wyoming statute sets a stricter minimum tread depth of 4/32 inch for tires on the front wheels of a bus, truck, or truck tractor, compared with 2/32 inch for tires in other cases.
-
49. At what time of day do drowsy driving crashes occur most often?
Show answer
Answer A: Between midnight and 6 a.m.
The body clock makes people sleepiest in the early morning hours, which is when most fatigue-related crashes happen.
-
50. Which factors determine a safe speed for a long, steep downgrade?
Show answer
Answer C: The steepness and length of the grade, the weight of the vehicle and cargo, and the road and weather conditions
Gravity, weight and traction all decide how fast a heavy vehicle can safely descend, which is why signs often post lower speeds for trucks on grades.